Jiangyin Jiangnan Metal Co., Ltd. | Open-Die Forging Factory Tel: +86-189-2135-9659  |  Email: sales@steelforgepieces.com
Jiangyin Jiangnan MetalOpen-Die Forgings & Rolled Rings

UNS S15700 (15-7Mo / AISI 632) Forgings

We make UNS S15700 forged rings, rolled rings, shafts, discs, flanges, bars, sleeves and bushings to ASTM A705 Type 632, forged to your drawing at our factory in Jiangyin, China.

ASTM A705 Type 632EAF + VOD + ESRUT to ASTM A388 / EN 10228-3EN 10204 3.1 / 3.2
Request a Quote

What Is UNS S15700?

UNS S15700, also called PH 15-7 Mo or AISI 632, is a chromium-nickel-molybdenum-aluminum semi-austenitic precipitation hardening stainless steel. It offers high strength and hardness, good corrosion resistance and low distortion during heat treatment.

The grade is close to 17-7PH. The difference is that about 2% chromium is replaced with 2% molybdenum, so 15-7Mo has higher strength at room temperature and at elevated temperatures.

UNS / AISI
S15700 / Type 632
Other names
PH 15-7 Mo, 15-7PH, 15-7Mo
W.Nr.
1.4532
Forgings
ASTM A705/A705M Type 632
Plate / sheet / strip
ASTM A693 Gr 632, AMS 5520
Other specs
MIL-S-8955, AMS 5812, AMS 5813

UNS S15700 Forged Products

All parts are forged to customer drawings or sizes and can be supplied as forged, rough machined or finish machined.

Forged and Rolled Rings
Seamless rolled rings, seal rings, retaining rings
Forged Shafts
Pump shafts, spindles, stepped shafts
Forged Discs and Blocks
Discs, blanks, valve blocks
Forged Flanges
Standard and drawing-based flanges
Forged Bars
Round and square forged bars
Sleeves and Bushings
Hollow forgings and forged tubes

Chemical Composition

UNS S15700 chemical composition, weight %
ElementMinMax
Carbon (C)-0.09
Manganese (Mn)-1.00
Silicon (Si)-1.00
Phosphorus (P)-0.040
Sulfur (S)-0.040*
Chromium (Cr)14.0016.00
Nickel (Ni)6.507.75
Molybdenum (Mo)2.003.00
Aluminum (Al)0.751.50

*Some specifications limit sulfur to 0.030%. The specification on your purchase order applies.

Heat Treatment

Hardening 15-7Mo takes three steps: austenite conditioning, cooling to transform austenite to martensite, and precipitation hardening. Forgings are first solution treated to Condition A at 1950°F (1066°C) and air cooled. We do both solution treatment and aging in house.

Standard heat treatment for UNS S15700
ConditionConditioning and transformationPrecipitation hardening
TH10501400°F (760°C) for 90 min, cool to 55°F (13°C) within 1 h, hold 30 min1050°F (566°C) for 90 min, air cool
RH9501750°F (954°C) for 10 min, cool to room temperature, within 1 h cool to -100°F (-73°C) and hold 8 h, warm in air950°F (510°C) for 90 min, air cool

Condition CH900 is produced by cold rolling at the mill and applies to strip only, not to forgings.

Mechanical and Physical Properties

Typical room temperature mechanical properties of 15-7Mo
ConditionTensile, ksi (MPa)0.2% Yield, ksi (MPa)Elongation in 2 in, %Hardness
A130 (896)55 (372)35HRB 88
TH1050210 (1448)200 (1379)7HRC 44
RH950240 (1655)225 (1552)6HRC 48

Typical values, not specification minimums. Properties of forgings vary with section size and are certified to ASTM A705 or the customer specification.

Physical properties
PropertyCondition ATH1050RH950
Density, g/cm³ (lb/in³)7.80 (0.282)7.69 (0.277)7.68 (0.277)
Modulus of elasticity, GPa-200200

Corrosion Resistance, Welding and Machining

Corrosion resistance

In TH1050 and RH950, general corrosion resistance is better than 410, 420 and 431 stainless steels, but slightly below Type 304.

Welding

15-7Mo can be welded by common fusion and resistance methods, though it is harder to weld than 17-4PH. The high aluminum content reduces penetration and increases slag. To get full strength back after welding, the part has to go through austenite conditioning and precipitation hardening again. W 15-7 Mo or W 17-7 PH filler metal is normally used.

Machining

Rough machining is best done in Condition A. After hardening to TH1050 or RH950 the material is much harder, so finish turning, milling and drilling need rigid setups and carbide tools.

Applications

15-7Mo is chosen for parts that need high strength at temperatures up to about 900°F (482°C) together with moderate corrosion resistance. Typical forged parts include retaining rings, aerospace structural fittings, pump and valve shafts, valve stems and seats, high strength rings and sleeves, and spring and diaphragm parts.

Production and Inspection

UNS S15700 forging process at Jiangyin Jiangnan Metal
MeltingEAF + VOD + ESR (electroslag remelting)
ForgingOpen-die forging and ring rolling
Heat treatmentSolution treatment and aging, TH1050 / RH950 or as specified
Ultrasonic testingASTM A388, EN 10228-3, SEP 1921
CertificatesEN 10204 3.1, or 3.2 with third-party inspection

FAQ

What is UNS S15700?

UNS S15700 (PH 15-7 Mo, AISI 632) is a Cr-Ni-Mo-Al semi-austenitic precipitation hardening stainless steel with high strength, good corrosion resistance and low distortion during heat treatment.

Which ASTM standard applies to UNS S15700 forgings?

ASTM A705/A705M Type 632. Plate, sheet and strip are supplied to ASTM A693 Grade 632 and AMS 5520.

What is the difference between 15-7Mo and 17-7PH?

15-7Mo replaces about 2% chromium with 2% molybdenum, which gives higher strength at room and elevated temperatures.

Can 15-7Mo be supplied in H900?

No. H900 is a 17-4PH condition. For 15-7Mo forgings the usual conditions are A, TH1050 and RH950.

How does its corrosion resistance compare with 410 and 304?

In TH1050 and RH950 it is better than 410, 420 and 431, but slightly below 304.

Where can I buy UNS S15700 forgings in China?

Jiangyin Jiangnan Metal Co., Ltd. in Jiangyin, Jiangsu makes UNS S15700 forged rings, shafts, discs, flanges and bars to ASTM A705 Type 632. Email sales@steelforgepieces.com or call +86-189-2135-9659.

Request a Quote

Please send your drawing or dimensions, quantity, heat treatment condition and required specification. We will reply with price and delivery time.

Jiangyin Jiangnan Metal Co., Ltd.
Address: No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Tel: 0086-189-2135-9659
Email: sales@steelforgepieces.com

Send Drawing

Technical data for reference only, based on ASTM A705 and published producer data. Last updated .