Open-Die Forging Factory, Jiangyin, Jiangsu, China EN 10204 3.1 / 3.2 certificates
Jiangyin Jiangnan Metal Co., Ltd. Open-Die Forgings and Seamless Rolled Rings

UNS S31254 Forgings 254 SMO, ASTM A182 Grade F44, EN 1.4547, 6Mo super austenitic stainless steel

Jiangyin Jiangnan Metal Co., Ltd. forges UNS S31254 to customer drawings as seamless rolled rings, flanges, round bars, discs, shafts, sleeves, bushings, tube sheets and forged pipe. Material is melted by EAF plus VOD, with ESR on request, annealed, ultrasonically tested to EN 10228-3, SEP 1921 or ASTM A388, and certified to EN 10204 3.1 or 3.2.

  • PREN above 43
  • Mo 6.0 to 6.5 percent
  • N 0.18 to 0.25 percent
  • Tensile min 650 MPa
  • Seawater and FGD service

Grade at a glance

UNS number
S31254
Forging specification
ASTM A182 F44
EN designation
1.4547
Common names
254 SMO, 6Mo
Structure
Super austenitic
Tensile, min
650 MPa / 94 ksi
Yield 0.2 pct, min
300 MPa / 44 ksi
Elongation, min
35 percent
Density
8.0 g/cm³
Hardenable
No, cold work only

What UNS S31254 is

UNS S31254 is a 6 percent molybdenum, nitrogen-alloyed super austenitic stainless steel, known commercially as 254 SMO and designated ASTM A182 Grade F44 in forged form and EN 1.4547 in Europe. The high molybdenum and nitrogen content give it a pitting resistance equivalent number above 43, comparable to a super duplex, along with resistance to chloride stress corrosion cracking, pitting and crevice corrosion, impact toughness, and roughly twice the strength of the 300 series stainless steels.

It is not a duplex grade. The structure is austenitic, so yield strength is lower than duplex and much lower than super duplex, and the alloy cannot be hardened by heat treatment. Because the higher alloy content makes it a more expensive choice, it is specified mainly where the service temperature falls outside the range suited to a super duplex.

1. Chemical composition

The table gives the composition limits for forgings to ASTM A182 / A182M Grade F44, alongside a typical analysis for the grade. Approximately 20 percent chromium, 18 percent nickel, 6 percent molybdenum and 1 percent copper define the alloy.

UNS S31254 and ASTM A182 F44 chemical composition, weight percent
ElementA182 F44 limitTypicalFunction
Carbon, C0.020 max0.010Held low to avoid carbide sensitisation
Silicon, Si0.80 max-Deoxidiser
Manganese, Mn1.00 max-Austenite stabiliser
Phosphorus, P0.030 max-Residual
Sulphur, S0.010 max-Low sulphur aids cleanliness
Chromium, Cr19.50 to 20.5020.0Passive film former
Nickel, Ni17.50 to 18.5018.0Austenite stability
Molybdenum, Mo6.00 to 6.506.1Pitting and crevice corrosion resistance
Copper, Cu0.50 to 1.001.0Resistance to reducing acids
Nitrogen, N0.18 to 0.250.20Raises strength and PREN
Iron, FeBalance55.69Base

Sulphur is shown as 0.010 max in line with normal practice for this grade. Published reproductions of the A182 table are not consistent on this figure, so the current edition of ASTM A182 / A182M and the purchase specification govern. Nitrogen is limited to 0.18 to 0.22 percent in some other product standards. The ladle analysis is confirmed on the EN 10204 certificate before despatch.

2. Mechanical and physical properties

Specification minima are the values certified on the test report. Typical values describe annealed material of moderate section and are not a specification guarantee.

Room temperature mechanical properties
PropertyASTM A182 F44 minimumTypical
Tensile strength650 MPa / 94 ksi680 MPa / 98,600 psi
Yield strength, 0.2 percent offset300 MPa / 44 ksi300 MPa / 43,500 psi
Elongation in 50 mm or 4D35 percent50 percent
Reduction of area50 percent-
Hardness, BrinellNot specified210 HBW
Physical and thermal properties
PropertyMetricImperial
Density8 g/cm³0.289 lb/in³
Modulus of elasticity195 GPa28,300 ksi
Shear modulus75 GPa10,900 ksi
Poisson ratio0.300.30
Thermal conductivity14 W/m·K97.2 BTU·in/hr·ft²·°F
Thermal expansion, 20 to 100 °C16.5 µm/m·°C9.17 µin/in·°F
Pitting resistance equivalent numberAbove 43

3. Forging, heat treatment, machining and welding

Hot working

Forging, upsetting and related operations are carried out at 982 to 1149 °C, that is 1800 to 2100 °F. Temperatures above this range cause scaling and reduce workability, so finishing temperature is controlled on heavy sections. Annealing after forging is advisable to recover maximum corrosion resistance.

Annealing

Annealing is performed at 1149 to 1204 °C, that is 2100 to 2200 °F, followed by a water quench. The purpose is to restore corrosion resistance, not to raise hardness.

Hardening and cold working

The alloy does not respond to heat treatment. Hardening is possible only through cold reduction. Cold working can be carried out by all the usual methods, although the high work hardening rate makes it demanding, and the result is increased strength and toughness.

Machining

Machining is difficult because of the very high work hardening rate and the absence of sulphur. Sharp tools, overpowered machine tools, positive feeds, slow speeds and generous lubrication give good results. Allow for lower metal removal rates than 316L when planning delivery.

Welding

Filler metal is required, since welding without it gives poor strength properties. Recommended filler metals are AWS A5.14 ERNiCrMo-3 and alloy 625 types. Electrodes should match AWS A5.11 ENiCrMo-12.

4. Specifications and equivalents

Designations and product standards covering UNS S31254
ReferenceScope
UNS S31254Unified Numbering System designation, S indicating stainless steel
ASTM A182 / A182M F44Forgings, flanges, fittings and valve components
EN 1.4547European material number
ASTM A240Plate, sheet and strip
ASTM A312Seamless pipe
ASTM A249 and A269Tube
ASTM A813 and A814Welded pipe
254 SMO, 6MoCommon trade and shop names for the grade

Buyers reach this grade from two directions. Either 316L has run out of chloride resistance, or a super duplex cannot be used because the service temperature sits outside its working range. We also forge the alternatives, so if a duplex or super duplex grade such as A182 F51, A182 F53 or A182 F55 suits the duty better, or a leaner austenitic such as 904L is sufficient, we will say so at enquiry stage.

5. Forged products in UNS S31254

Every item is made to the customer drawing or dimensional requirement, in the as-forged, rough machined or finish machined condition.

Seamless rolled rings and forged rings

Ring rolled for continuous circumferential grain flow. Used in plant cooled by seawater, offshore structures, and gear and bearing blanks.

Flanges and tube sheets

Weld neck, slip-on, blind and special flanges, tube sheets and separator parts for heat exchangers, firewater and subsea pipework, risers and manifolds.

Round bars, shafts and spindles

Forged round bar, straight and eccentric shafts, spindles and gear blanks for power transmission, turbines, gas compressors and gearboxes.

Discs and blanks

Upset forged discs and disks for valve internals, industrial air compressors, power generators and nitrogen generators.

Sleeves and bushings

Forged sleeves and bushings for subsea and deepwater oil production systems, down-hole hardware and waste water plant.

Forged pipe, tubes and nozzles

Forged pipe, tubes and nozzles for chloride bearing and mixed acid duty, including pressure vessel components.

Valve components

Valve bodies, stems, seat rings and blocks for ball, gate, globe, check and plug valves and strainers.

Rolls, wheels and manifolds

Forged rolls, wheels and manifolds for desalination plant, high pressure reverse osmosis systems, seawater piping and power industry FGD systems.

Crankshafts and custom work

Forged crankshafts and open-die forgings for mechanical and structural components.

6. Testing, certification and traceability

Standard scope supplied with UNS S31254 forgings
StageScope
MeltingEAF plus VOD refining, with ESR available for critical or heavy section parts
Chemical analysisLadle analysis reported element by element
Mechanical testingTensile strength, yield strength, elongation, reduction of area and hardness
Ultrasonic testingEN 10228-3, SEP 1921 or ASTM A388 to the agreed acceptance class
DocumentationEN 10204 3.1 works certificate, or 3.2 with third party witness
MarkingHeat number, grade, specification and customer item number for full traceability

Additional corrosion testing, impact testing or inspection by a named third party can be added to the order on request. State the requirement at enquiry stage so that it is priced in.

7. Applications

UNS S31254 earns its cost where chlorides, acids and temperature act together. Published application areas for the grade include saltwater handling, flue gas desulphurisation scrubbers, flue gas cleaning, desalination, heat exchangers, components used in petroleum production, process equipment in the chemical industry, tall oil distillation columns, food processing equipment, and bleaching equipment in the pulp and paper industry. For certain applications the grade has been reported as a cost effective substitute for high nickel and titanium alloys.

In forged form the recurring items are tube sheets and flanges for seawater cooled heat exchangers, separator and riser components for offshore plant, scrubber hardware for FGD systems, high pressure parts for reverse osmosis desalination plant, and valve bodies and stems for chloride bearing acid service.

8. Frequently asked questions

Is UNS S31254 a duplex stainless steel?
No. It is a super austenitic stainless steel, also called 254 SMO or 6Mo. It reaches a PREN above 43, comparable to a super duplex, through about 6 percent molybdenum plus nitrogen, but the structure is austenitic and the yield strength is lower than duplex and much lower than super duplex.
Which specification covers S31254 forgings?
ASTM A182 / A182M Grade F44 for forgings, flanges, fittings and valve components. Other forms fall under ASTM A240 for plate, A312 for seamless pipe, A249 and A269 for tube, and A813 and A814 for welded pipe. The European designation is EN 1.4547.
What minimum values appear on the test certificate?
Tensile strength 650 MPa, that is 94 ksi, minimum. Yield strength at 0.2 percent offset 300 MPa, that is 44 ksi, minimum. Elongation 35 percent minimum in 50 mm or 4D. Reduction of area 50 percent minimum. ASTM A182 F44 sets no Brinell hardness limit, although around 210 HBW is typical.
Can the grade be quenched and tempered to raise strength?
No. It does not respond to heat treatment. The cycle after forging is an anneal at 1149 to 1204 degrees Celsius with a water quench, which restores corrosion resistance. Extra strength is obtainable only by cold reduction.
What sizes and weights can you forge?
Open-die and ring rolled parts are made to the customer drawing. Send the drawing, or the outside diameter, inside diameter and height or length with the quantity, to sales@steelforgepieces.com and we will confirm feasibility, weight and lead time against current press and ring mill capacity.
What do you need in order to quote?
Grade and specification, for example A182 F44, the drawing or dimensions, quantity, delivery condition as-forged or rough machined or finished, the ultrasonic acceptance class, certificate type EN 10204 3.1 or 3.2, and the destination port.

9. Basis of the data

Composition limits and mechanical minima on this page are stated against ASTM A182 / A182M Grade F44. Physical and thermal values, hot working and annealing ranges, machining and welding practice and the application list follow published datasheet values for UNS S31254 and 254 SMO. The PREN figure follows published values for the grade of above 43. Values marked typical are indicative and are not a specification guarantee. For any order the governing documents are the purchase specification agreed in writing and the current edition of the applicable ASTM or EN standard.

Prices are quoted per drawing and per heat, so no price is published on this page. 254 SMO is a trademark of its owner and is used here only to identify the grade. Technical data last reviewed October 2026.

Request a quotation for UNS S31254 forgings

Send a drawing or your dimensions and we will quote weight, price and lead time.

Company
Jiangyin Jiangnan Metal Co., Ltd.
Open-Die Forging Factory
Works address
No.1 Chengxiqiao Road, Zhouzhuang Town,
Jiangyin City, Jiangsu Province, China
Telephone
+86 189 2135 9659

Send drawing and get a quote