Open-Die Forging Factory, Jiangyin, Jiangsu, China 0086-189-2135-9659 | sales@steelforgepieces.com
Request a Quotation

UNS S20910 (XM-19) Open-Die Forgings

Forged rings, seamless rolled rings, flanges, shafts, discs, sleeves and bars to AMS 5764, ASTM A182 F XM-19 and DIN 1.3964

UNS S20910 is a nitrogen-strengthened austenitic stainless steel, listed as XM-19 by ASTM and as 1.3964 in the Werkstoff system. Its yield strength is close to twice that of annealed 304 and 316, and its corrosion resistance is higher than both. Jiangyin Jiangnan Metal Co., Ltd. forges this grade to customer drawings. Material is melted by EAF plus VOD or by ESR, solution annealed, ultrasonically tested and supplied with EN 10204 3.1 or 3.2 certification.

Chemical composition

Chromium and molybdenum provide pitting resistance. Nickel keeps the structure austenitic and maintains toughness at low temperature. Manganese and nitrogen act as solid solution strengtheners, and nitrogen in the range 0.20 to 0.40 percent is the element that separates this grade from the standard 300 series. Niobium and vanadium stabilise carbides and help control grain size.

Table 1. UNS S20910 / XM-19 chemical requirements, weight percent
LimitCSiMnPSCrNiMoNNbVFe
Min--4.00--20.5011.501.500.200.100.10Balance
Max0.061.006.000.0400.03023.5013.503.000.400.300.30

Limits as published for XM-19 / UNS S20910 by AZoM and Aircraft Materials. Heat analysis for each order is reported on the mill certificate.

Mechanical properties

Solution annealed condition, AMS 5764

Table 2. Minimum room temperature properties, annealed
PropertyImperialMetric
Ultimate tensile strength, min100 ksi690 MPa
Yield strength, 0.2 percent offset, min55 ksi380 MPa
Elongation, min35 %35 %
Reduction of area, min55 %55 %
Hardness, max as supplied by us293 HBW
Density0.285 lb/in³7.88 to 7.89 g/cm³
Mean thermal expansion, 25.6 to 93.3 °C9 µin/in · °F16.2 µm/m · °C

Strain hardened levels

This grade cannot be hardened by heat treatment. Higher strength is obtained by cold work. The levels below are published for bar. The level that can be reached depends on section size, and for sour service the NACE hardness limit normally governs the choice.

Table 3. Strain hardened minimum properties for bar, per Aircraft Materials data
LevelDiameterUTS min, ksiYS min, ksiElongation minRA min
HS 10.125 to 4.00 in1109035 %55 %
HS 20.125 to 4.00 in13510520 %50 %
HS 30.125 to 3.50 in16013015 %45 %
HS 40.062 to 2.00 in18014512 %45 %
HS 50.062 to 1.50 in20018010 %45 %

Corrosion resistance and sour service

The higher chromium and molybdenum content gives a pitting resistance equivalent number of about 34, against 25 for 316L. Super duplex grades reach above 40, but with different mechanical behaviour, which is one reason buyers select UNS S20910 where austenitic ductility, cryogenic toughness and low magnetic permeability are required. The grade is listed in NACE MR0175 for sour service on the basis of its resistance to sulphide stress cracking, and it also resists intergranular attack.

Table 4. PREN comparison
GradePREN
Alloy 316L25
UNS S20910 (XM-19)about 34
Super duplex stainless steelabove 40

PREN values as published by Langley Alloys.

Forging, heat treatment and machining

The alloy forges well but needs more power than the 300 series. Published data places hot working between about 1150 and 1232 °C (2100 to 2250 °F), with rapid cooling after forging rather than slow air cooling. Solution annealing follows at 1066 to 1121 °C (1950 to 2050 °F) with a rapid quench. For most applications the 1950 °F condition is selected, because it gives a higher level of mechanical properties together with good corrosion resistance. When as-welded material will be used in strongly corrosive media, the 2050 °F condition is specified in order to reduce the possibility of intergranular attack.

For machining, the work hardening rate is the limiting factor. Low cutting speeds should be used compared with low-alloyed standard austenitic stainless steels, together with positive uninterrupted feeds, rigid set-ups, sharp tooling and ample coolant. Allowing the tool to dwell in the cut is the usual cause of premature tool failure on this material.

Specifications and equivalent designations

Table 5. Designations covering UNS S20910
CategoryDesignation
UNSS20910
ASTM generic gradeXM-19
Werkstoff / EN1.3964, X2CrNiMnMoNNb21-16-5-3
AerospaceAMS 5764, bar, forgings and rings
Forgings and fittingsASTM A182 F XM-19, A336 XM-19, A403 XM-19, A965
Bar and shapesASTM A276, A479 XM-19, A580 XM-19, A314
Plate, sheet and tubeASTM A240, A249, A269, A312, A412, A813 TP XM-19
FastenersASTM A193 Gr. B8R and B8RA, ASTM A194 Gr. B8R and B8RA
Welding consumableAWS A5.9 ER209
Trade names for the same chemistryNitronic 50, Fermonic 50, ATI 50

Nitronic, Fermonic and ATI 50 are trademarks of their respective owners. Jiangyin Jiangnan Metal Co., Ltd. supplies the generic UNS S20910 / XM-19 chemistry and is not affiliated with those trademark holders.

Forging forms we supply in UNS S20910

Seamless rolled rings

Rolled on radial and axial mills for valve bodies, pump casings, flange blanks and bearing races, with grain flow following the circumference.

Shafts and spindles

Pump shafts, boat shafting, eccentric shafts, turbine and gearbox shafts, straight or stepped, rough turned or finish machined.

Flanges and tube sheets

Weld neck, slip-on, blind and special profile flanges, plus heat exchanger tube sheets in large diameters.

Discs, blanks and hubs

Upset forged discs for closures, gear blanks, wheels and manifold bodies.

Sleeves, bushings and forged tubes

Hollow forged and bored sections for subsea housings, compressor parts and wear sleeves.

Bars and blocks

Forged round bar, square and rectangular blocks for valve stems, seat rings, bodies and downhole tooling.

Typical applications

In chemical and fertiliser plant the grade is used for urea production equipment, ammonium carbamate pumps, pressure vessels, tanks, heat exchangers, piping, fittings, valves and pumps. Marine and subsea users specify it for seawater pumps, gate valves in tanker ballast systems, deep sea sampling and incubation chambers, underwater robotic arms and rigging. Oil and gas operators use it for subsea and deepwater production systems, wellheads and Christmas trees, downhole and oilfield production equipment, industrial air compressors, power generators and nitrogen generators. Valve makers use it for stems, seat rings, bodies, blocks and internals in ball, gate, globe, check and plug valves. Other uses include nuclear waste handling such as calcination systems, aqueous fluoride handling systems and waste canisters, together with power transmission, turbines, gas compressors, gearboxes, pulp and paper, pharmaceutical and biochemical equipment and shipbuilding.

Quality control and documentation

Melting is by EAF plus VOD, with ESR available where lower inclusion content is required. Every forging is solution annealed and quenched, then ultrasonically tested to EN 10228-3, SEP 1921 or ASTM A388 as specified on the order. Testing on request covers tensile and hardness, sub-zero impact, intergranular corrosion to ASTM A262, PMI and magnetic permeability. Certificates are issued to EN 10204 3.1, or to 3.2 with third party witness by BV, SGS, TUV, DNV or Lloyd's Register.

Send your drawing for a quotation

Please provide the grade, dimensions or drawing, quantity, applicable standard and the certification level required. Single pieces and series production are both accepted.

sales@steelforgepieces.com 0086-189-2135-9659

Frequently asked questions

What is UNS S20910?

A nitrogen-strengthened austenitic stainless steel, listed as XM-19 by ASTM and as 1.3964 in the Werkstoff system. It contains 20.5 to 23.5 percent chromium, 11.5 to 13.5 percent nickel, 4 to 6 percent manganese, 1.5 to 3 percent molybdenum and 0.20 to 0.40 percent nitrogen. Yield strength is close to twice that of annealed 304 and 316, with higher corrosion resistance.

Is UNS S20910 the same alloy as Nitronic 50?

Nitronic 50 is a trade name for the alloy covered by UNS S20910. The generic ASTM designation is XM-19 and the European equivalent is 1.3964, X2CrNiMnMoNNb21-16-5-3. The same chemistry is also sold as Fermonic 50 and ATI 50.

What are the minimum annealed mechanical properties?

To AMS 5764: 100 ksi (690 MPa) tensile strength, 55 ksi (380 MPa) yield strength at 0.2 percent offset, 35 percent elongation and 55 percent reduction of area.

What forging and annealing temperatures apply?

Hot forging is published at about 1150 to 1232 °C (2100 to 2250 °F) with rapid cooling afterwards. Solution annealing is at 1066 to 1121 °C (1950 to 2050 °F) followed by rapid quench. Use the 2050 °F condition when as-welded material will see strongly corrosive media.

How does it compare with 316L for corrosion resistance?

PREN is about 34 against 25 for 316L, due to the higher chromium and molybdenum content. The grade is listed in NACE MR0175 for sour service.

Why is the grade difficult to machine?

It has a high work hardening rate, so only low cutting speeds should be used compared with low-alloyed standard austenitic stainless steels. Rigid tooling, continuous feed and good coolant supply are required.

Can it be hardened by heat treatment?

No. Like other austenitic stainless steels it is hardened only by cold work. Strain hardened bar is available from 110 ksi up to 200 ksi minimum tensile strength.

Who supplies UNS S20910 open-die forgings from China?

Jiangyin Jiangnan Metal Co., Ltd., No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China. The factory produces rings, rolled rings, flanges, shafts, discs, sleeves, bushings, tube sheets and bars in this grade to drawing, with EN 10204 3.1 or 3.2 certification and ultrasonic testing to EN 10228-3, SEP 1921 or ASTM A388. Telephone 0086-189-2135-9659, email sales@steelforgepieces.com.

Buyers comparing this grade also look at Nitronic 60 for galling resistance, 17-4PH and 15-5PH where precipitation hardening is acceptable, A286 for elevated temperature bolting, and Incoloy 825 or Inconel 625 when chloride and sour service conditions exceed the limit of an austenitic stainless steel.

Reviewed October 2026 by Jiangyin Jiangnan Metal Co., Ltd. Technical data compiled from AMS 5764 and ASTM published limits and from public datasheets issued by AZoM, Aircraft Materials and Langley Alloys. Figures are for guidance. Order specific results are confirmed on the mill certificate.