Jiangyin Jiangnan Metal Co., Ltd. | Open Die Forging Factory, Jiangyin, China Tel, WhatsApp, WeChat: 0086-189-2135-9659 Email: sales@steelforgepieces.com
Jiangyin Jiangnan Metal Melting · Open Die Forging · Ring Rolling

UNS S21800 is a high silicon, high manganese, nitrogen strengthened austenitic stainless steel. The silicon and manganese additions inhibit wear, galling and fretting even in the annealed condition, giving galling resistance superior to that of any other stainless steel. That is why it replaces cobalt bearing and high nickel alloys in valve stems, seats and trim, pump wear rings, bushings, pins and fasteners at significantly lower cost. Yield strength is roughly twice that of 304 and 316, chloride pitting resistance is better than 316, and the grade is not hardenable by heat treatment.

Jiangyin Jiangnan Metal Co., Ltd. forges this grade to drawing at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China. The plant melts its own steel through EF, LF and vacuum oxygen decarburisation, with vacuum and electroslag remelting available, so the nitrogen content S21800 depends on is set at the furnace instead of being accepted from a purchased billet certificate.

Designations and specifications

UNS S21800 cross reference
UNS numberS21800
Trade namesNitronic 60, Fermonic 60
Alloy designationAlloy 218
Bar, forgings and wireAMS 5848
Bar and shapesASTM A276 / ASME SA276
Sheet and plateASTM A240 / ASME SA240
Alloy classFully austenitic, non magnetic, nitrogen strengthened

Confirm the applicable specification edition when ordering, and state which mechanical properties are to be certified and at what section size, so the test pieces are planned before the forging is heat treated rather than afterwards.

Chemical composition

Composition limits, weight percent
ElementMinimumMaximum
Carbon–0.10
Manganese7.09.0
Silicon3.54.5
Chromium16.018.0
Nickel8.09.0
Nitrogen0.080.18
Molybdenum–0.75
Phosphorus–0.060
Sulfur–0.030
IronBalance

Some producers publish a narrower nominal manganese range for this grade. Both sets of limits are in circulation, so name the specification and edition you are buying to and the heat will be aimed at that range.

Mechanical properties

Solution annealed condition, minimum values
PropertyValue
Ultimate tensile strength95 ksi (655 MPa)
Yield strength at 0.2 % offset50 ksi (345 MPa)
Elongation35 %
Reduction of area55 %
Hardness, Brinell, maximum241
Density0.275 lb/in³ (7.61 g/cm³)

Room temperature yield strength is approximately twice that of Type 304 and Type 316, so a thinner section will often carry the same load. The grade cannot be hardened by heat treatment. Higher strength comes only from cold work, and cold work does not improve the galling behaviour, so parts chosen for galling resistance are normally left in the annealed condition.

Galling and wear behaviour

Galling occurs when two loaded metal surfaces micro weld across their contact faces and tear on separation. In a wear system the galling or seizure failure normally comes first, followed by dimensional loss from wear, and only then corrosion. That sequence is the reason S21800 is specified in preference to a more corrosion resistant grade for parts that slide, rotate or have to be dismantled and reassembled.

Because of its grain structure, the galling resistance of S21800 is superior to that of any other stainless steel, and it resists wear, tearing and seizure of both itself and the mating material across a wide temperature range. The important practical point is that this behaviour is present in the annealed condition, so it does not depend on a hardening treatment, a surface coating or a lubricant. That makes the grade useful in food, pharmaceutical and sanitary equipment where lubricants are not permitted, and in fasteners that have to come apart again without the threads tearing up.

Detailed threshold galling stress and wear compatibility test matrices for S21800 against 304, 316, 410, 440C, 17-4PH and other couples are published in the producer data bulletins cited at the foot of this page, and can be sent on request against your specific contact pair and loading.

Corrosion resistance

Uniform corrosion resistance is superior to Type 304 in most media, but is not as good as Type 316. What the grade offers over 316 is better chloride pitting resistance, better stress corrosion cracking resistance and better crevice corrosion resistance, which is the combination that matters in seawater and produced water service.

Read that trade honestly when selecting. If the duty is uniform corrosion in a warm acid, 316 or a higher alloy is the better material and S21800 is the wrong answer. If the duty involves chlorides, crevices, sliding contact or repeated dismantling, S21800 usually wins because it addresses the failure mode that actually removes the part from service.

High temperature behaviour

Oxidation resistance is far superior to Type 304 and Type 316 and comparable to Type 309. Carburisation resistance is superior to 316L and 309. The alloy was originally developed as a high temperature material and performs well to around 1800 °F (980 °C), and as an austenitic grade it also retains good impact resistance at low temperature. For continuous service at the top of the range, compare it against a purpose built heat resisting grade before committing, since the dedicated heat resisting alloys outperform it on static oxidation.

Forged shapes produced in UNS S21800

Rolled and forged rings

Seamless rolled rings on the 6 m ring mill, contoured rings, retaining rings, pump wear rings and valve seat rings.

Flanges and tube sheets

Forged flanges, tube sheets, covers, nozzles and manifolds, supplied proof machined where volumetric inspection is required.

Shafts, stems and bars

Stepped shafts, spindles, eccentric shafts, valve stems, bridge pins, round bars, flat bars and square bars.

Discs, sleeves and bushings

Solid forged discs, blanks, hubs, sleeves, bushings, rollers and gear ring blanks.

Valve and wellhead parts

Valve bodies, bonnets, blocks, stems, seat rings, spools, trim and down hole components.

Cylinders and heavy wall pipe

Hollow forged cylinders and heavy wall pipe sections bored from solid forged blanks.

Where the grade is used

Oil and gas production

Pump wear rings, bushings, valve trim, seals, fittings, screens and down hole equipment.

Marine and seawater service

Seawater pump components, gate valves for tanker ballast systems, and submerged hardware where chloride pitting resistance and galling resistance are both required.

Chemical, petrochemical and process plant

Process valve stems, seats and trim, pump wear rings and lobes.

Food, pharmaceutical and surgical equipment

Galling resistant sliding parts in sanitary equipment where lubricants cannot be used.

Infrastructure and hydro power

Bridge pins, pin and hanger expansion joints and wear plates, chosen for better corrosion and galling resistance plus low temperature toughness compared with the carbon steels traditionally used, and stems and wicket gate wear rings in hydroelectric plant.

Power transmission and rotating equipment

Gear blanks, spindles, chain drive components, roller bearing parts, turbine and gas compressor components.

Why forge this grade at this plant

S21800 relies on nitrogen between 0.08 and 0.18 % for its strength, and on a tight silicon and manganese balance for its galling behaviour. A forge that buys billet inherits whatever chemistry the billet supplier delivered. This works melts its own steel and the material moves through the presses, the ring mill, the heat treatment furnaces and the machine shop without leaving the site, so traceability runs from the melt number to the shipped part.

Works capability
MeltingEF, LF, VOD, VIM, VAR and ESR. Maximum heat 60 t
Forging6,300 t open die hydraulic press
Ring rolling6 m ring mill
Maximum single piece30 t
Heat treatment14 furnaces
Established1997
People460, including 9 senior engineers, 32 intermediate engineers and 140 technicians
Class approvalsCCS, BV, DNV, LR, NK
Export marketsNorth America, Europe, Middle East, Asia-Pacific

Testing and certification

Forgings in this grade are ultrasonically tested to EN 10228-3, SEP 1921 or ASTM A388, whichever is specified on the order, with the acceptance class stated by the customer. Certificates are issued to EN 10204 3.1, or to EN 10204 3.2 witnessed by a third party inspection body. Pitting, intergranular corrosion and sub zero impact testing can be placed with an accredited laboratory and reported alongside the mill certificate. State these requirements on the enquiry so they are scheduled into the route rather than added after heat treatment, when test material may no longer be available.

Request a quotation

Send these six items in the first email and a priced proposal can be prepared without further exchanges.

#ItemExample
1Grade and specificationUNS S21800, AMS 5848
2Dimensions or drawing (PDF, DWG, DXF, STEP)OD 620 × ID 440 × H 95 mm
3Quantity and expected repeat volume8 pcs, about twice a year
4Delivery conditionSolution annealed, proof machined
5Testing requirementsUT to EN 10228-3, tensile and hardness certified
6Certification and destination portEN 10204 3.2 witnessed, Houston

sales@steelforgepieces.com 0086-189-2135-9659

Jiangyin Jiangnan Metal Co., Ltd., No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China.

Frequently asked questions

What is UNS S21800 also called?
Nitronic 60, Fermonic 60 and Alloy 218 all refer to the same grade. Nitronic is a registered trademark of AK Steel and Fermonic is a Langley Alloys designation, so the UNS number is the safest way to specify it on a drawing.
Is UNS S21800 magnetic?
No. It is fully austenitic and non magnetic in the annealed condition.
Can it be hardened by heat treatment?
No. It is supplied solution annealed. Cold work is the only route to higher strength, and cold work does not improve the galling resistance.
Is S21800 or 316 the better choice?
For chloride pitting, crevice corrosion and stress corrosion cracking, S21800. For uniform corrosion in most acids, 316. If the part also slides or has to be dismantled, S21800 generally wins because galling is the failure mode that occurs first.
Will the mechanical properties be certified?
State which properties you need and at what section size and they will be tested and reported. Agreeing this at order stage matters, because test material has to be planned into the forging and heat treatment route.
Can you work from a sample or a damaged part instead of a drawing?
Yes. A sample part, a sketch with the critical dimensions, or a worn component can all be used as the basis for a forged blank proposal. Mark which features are functional and what tolerance they need.
Can we audit the plant or witness testing?
Yes. Customer audits, pre shipment inspection and third party witness testing are all welcome. Arrange visits by email in advance so an engineer is available.

Related grades

Forged product categories

Data sources. Composition limits, mechanical minimums, density and the qualitative galling, wear, corrosion, oxidation and carburisation comparisons on this page are drawn from published producer datasheets for UNS S21800 and Nitronic 60, namely the Carlson Alloy Nitronic 60 (UNS S21800) Product Data Bulletin from G.O. Carlson / Electralloy, the Rolled Alloys Nitronic 60 datasheet, the Aircraft Materials Nitronic 60 / AMS 5848 technical data sheet, and Langley Alloys technical resources. Values are typical or average except where stated as a minimum or a maximum, and nothing here is intended for specification purposes or as a warranty of fitness. As with any wear material, test it under your own service conditions before committing a design.

Works capability, workforce and class approval figures are Jiangyin Jiangnan Metal's own published plant data. Last updated .