Open-Die Forging Factory, Jiangyin, Jiangsu, China. Rolled rings, flanges, shafts, discs. +86-189-2135-9659  |  sales@steelforgepieces.com
Jiangyin Jiangnan Metal Co., Ltd. Open-die forgings, seamless rolled rings, forged flanges and shafts Request a Quote

UNS S31803 Duplex Stainless Steel Forgings

ASTM A182 Grade F51, EN 1.4462 / X2CrNiMoN22-5-3, duplex 2205. Open-die forged rings, flanges, shafts, discs, sleeves and bars made to drawing by Jiangyin Jiangnan Metal Co., Ltd.

UNS S31803 is a 22 percent chromium duplex stainless steel with a structure of roughly 50 percent ferrite and 50 percent austenite. The two phases together give about twice the yield strength of 304 or 316 austenitic stainless steel, along with better resistance to chloride pitting and stress corrosion cracking.

In forged form the grade is designated ASTM A182 Grade F51, with minimum requirements of 620 MPa tensile strength, 450 MPa yield strength, 25 percent elongation and a maximum hardness of 290 HBW, after solution annealing above 1020 C and rapid water quenching.

Jiangyin Jiangnan Metal Co., Ltd., No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, telephone +86-189-2135-9659, email sales@steelforgepieces.com, produces UNS S31803 open-die forgings to customer drawing with EN 10204 3.1 or 3.2 certification.

UNSS31803
Forging gradeASTM A182 F51
EN number1.4462
Structure50/50 duplex
Tensile min620 MPa
Yield min450 MPa
Hardness max290 HBW
Max service315 C

UNS S31803 Forgings We Produce

As an open-die forging works we produce every item from a forged billet to your drawing rather than machining it from plate or bar stock. Regular UNS S31803 deliveries cover seamless rolled rings, forged flanges, round bars, shafts and eccentric shafts, discs and blanks, sleeves, bushings, tube sheets, forged pipe and tube bodies, valve bodies, stems and seat rings, nozzles, manifolds, gear and spindle blanks, crankshafts and forged rolls. Rings can be supplied rough turned or finish machined. We quote from a dimensioned drawing showing tolerances and the machining allowance you require.

Chemical Composition, ASTM A182 F51 / UNS S31803

Chemical composition limits in weight percent, balance iron
ElementCMnPSSiCrNiMoN
UNS S31803 0.03 max2.00 max0.03 max0.02 max1.00 max 21.0-23.04.5-6.52.5-3.50.08-0.20

Nitrogen is the element that makes the grade work. It raises strength, stabilises the austenite phase and improves pitting resistance and weldability compared with the first generation of nitrogen-free duplex steels. Pitting resistance is normally estimated from PREN = percent Cr + 3.3 x percent Mo + 16 x percent N. For typical 2205 analyses the result falls in the mid 30s, with the exact figure depending on the certified analysis of the heat supplied.

Mechanical Properties

Minimum room temperature requirements, ASTM A182 Grade F51
GradeTensile strength minYield strength 0.2 percent minElongation minHardness max
F51 / S31803 620 MPa (90 ksi) 450 MPa (65 ksi) 25 percent 290 HBW

One tension test is taken per heat, together with one set of three Charpy V-notch impact specimens. Results on solution annealed forgings normally sit well above these minima. Where a design code or client specification calls for higher guaranteed values, tighter impact energy at low temperature or through-thickness testing, state this at enquiry stage so that forging reduction and test location can be planned before production.

S31803 or S32205: What to Specify

Both UNS numbers describe 22 percent chromium duplex 2205. S31803 was the original designation. Because mills consistently produced the grade towards the top of the permitted range, particularly on nitrogen, a tighter and higher-alloyed designation was introduced as UNS S32205, which appears in ASTM A182 as grade F60.

The relationship runs one way only. Material made to S32205 satisfies S31803 and can be dual certified as S31803, while S31803 on its own does not guarantee that S32205 is met. Where your project permits it, ordering dual certified S32205 and S31803 gives a higher guaranteed nitrogen floor, and therefore higher guaranteed pitting resistance, for the same part. We supply either designation, so state on the enquiry which certification the end client requires.

Equivalent Designations

Cross reference for 22 percent chromium duplex stainless steel
SystemDesignation
UNSS31803, tighter modern designation S32205
ASTM A182 forgingsF51, S32205 is F60
EN steel number1.4462
EN steel nameX2CrNiMoN22-5-3
JISSUS 329J3L
Market nameDuplex 2205

EN 1.4462 is written to a chemistry band that covers both the S31803 and S32205 designations, so a 1.4462 certificate on its own does not establish which UNS designation the heat satisfies. The actual analysis on the mill certificate has to be checked.

Melting, Forging and Heat Treatment

Our standard melting route for duplex forgings is electric arc furnace with VOD refining. ESR is available where a client specifies remelted material for improved cleanliness and homogeneity. Billets are forged with controlled reduction to break down the as-cast structure and to develop grain flow suited to the component, radial-axial rolling for rings and upsetting with drawing out for discs and shafts.

Heat treatment decides whether a duplex forging performs in service. After hot forging the part is cooled, then solution annealed above 1020 C, with 1020 to 1100 C being normal practice, soaked for a period matched to the section thickness, and water quenched rapidly. Speed of quench is critical. Slow cooling through the range of roughly 600 to 950 C precipitates sigma phase and other intermetallics that cut impact toughness and corrosion resistance. Heavy sections carry the greatest risk, so we plan quench orientation and water volume around the thickest part of the forging.

Corrosion Performance and Service Limits

In the solution annealed condition S31803 resists intergranular corrosion, helped by the carbon ceiling of 0.03 percent. Compared with the common austenitic grades it offers better general corrosion resistance than 316 and considerably higher resistance to chloride stress corrosion cracking than either 304 or 316, which is why the grade is widely used in seawater, brine and sour service.

Temperature is the limiting factor at both ends. S31803 is not normally used above about 315 C because extended exposure at moderately elevated temperature embrittles the ferrite phase. At cryogenic temperatures the ferrite phase also loses toughness, so low temperature duty calls for specific impact testing rather than assumption. Where service falls outside this window, an austenitic grade such as 904L or a nickel alloy such as Incoloy 825 or Inconel 625 is usually the better choice, and we forge those grades as well.

Machining Guidance

Duplex work hardens quickly and has high strength, so cutting speed must come down appreciably against 316 and 316L when turning with coated cemented carbide tooling. Feed should be reduced only slightly, since backing the feed off too far makes the tool rub instead of cut and accelerates work hardening. Use rigid setups, sharp inserts, positive rake, plenty of coolant, and a depth of cut that takes the tool below the work hardened layer left by the previous pass. The same principles apply to drilling and milling.

Applications for UNS S31803 Forgings

Oil, gas and offshore

Subsea and deepwater production systems, wellhead and Christmas tree components, forged flanges and pipe bodies, manifolds, and downhole components for moderately corrosive sour gas wells.

Chemical process and desalination

Separator and heat exchanger parts, forged tube sheets, crystalliser components, seawater desalination plant internals, and valve bodies, stems, seat rings and blocks for ball, gate, globe, check and plug valves.

Pulp and paper

Digesters, liquor tanks, paper machine components and forged rolls. Pulp and paper production was the original application for which duplex steels were developed in the 1930s.

Power, marine and rotating equipment

Rolled rings and forged shafts for power generation and marine service, compressor parts, industrial air compressors, nitrogen and power generator components, gearbox and turbine rings, spindle and gear blanks, shipbuilding and heavy machinery parts.

Testing, NDT and Certification

Ultrasonic examination of duplex forgings is carried out to EN 10228-4, the part of that standard covering austenitic and austenitic-ferritic stainless steel forgings. ASTM A388 is applied where a client specification calls for it. EN 10228-3 covers ferritic and martensitic forgings and is not the applicable part for S31803. Surface examination by liquid penetrant is available on request, and penetrant rather than magnetic particle is generally the appropriate method for this grade.

Where intermetallic phase content has to be demonstrated, we test to ASTM A923, using the sodium hydroxide etch, impact or corrosion test methods, or to ASTM A1084. Ferrite and austenite phase balance can be reported by point count or image analysis. Certification is issued to EN 10204 3.1, or to EN 10204 3.2 with witness and endorsement by your nominated third party inspection agency. Weld repair is not permitted on these forgings.

Frequently Asked Questions

Is UNS S31803 austenitic or duplex?
Duplex. The structure is approximately 50 percent ferrite and 50 percent austenite. The distinction has practical consequences, because duplex behaves differently from austenitic steel in heat treatment, welding, machining and elevated temperature service.
Can S32205 be supplied where S31803 is specified?
Yes. S32205 is the tighter, higher-alloyed designation and satisfies S31803, so it can be dual certified as S31803. The reverse does not hold, as S31803 alone does not guarantee S32205 compliance.
What sizes and weights can you forge?
Capability depends on the geometry of the specific part, so we quote against your drawing rather than publish a blanket size envelope. Send the dimensioned drawing, or the rough dimensions with the required finished size, plus quantity, governing specification and certification level, and we will confirm feasibility and price. Email sales@steelforgepieces.com or call +86-189-2135-9659.
Why does the quench after solution annealing matter so much?
Slow cooling through roughly 600 to 950 C precipitates sigma phase and other intermetallics, which sharply reduce impact toughness and corrosion resistance. Rapid water quenching from above 1020 C preserves the correct two phase balance. This is the main quality risk in heavy section duplex forgings and the reason ASTM A923 testing exists.
Can S31803 be used at high temperature?
No. Service above roughly 315 C risks embrittlement. For higher temperatures consider austenitic grades or nickel alloys such as Incoloy 800H and 800HT, Inconel 617 or Inconel 625, all of which we forge.
Which certificate is supplied?
EN 10204 3.1 as standard, or EN 10204 3.2 with third party inspection and endorsement. Certificates report heat analysis, mechanical and impact results, the heat treatment record, NDT results and any supplementary testing such as ASTM A923 or phase balance.

Send Your Drawing for a UNS S31803 Forging Quotation

Jiangyin Jiangnan Metal Co., Ltd. Open-die forging factory. No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China.

sales@steelforgepieces.com +86-189-2135-9659

Please include the grade and certification designation required, S31803 or dual S32205, the product form, rough or finished dimensions, quantity, governing specification, NDT requirement and certificate level.

Related Grades

Other duplex and corrosion resistant forging grades we supply: A182 F53, A182 F55, A182 F61, 904L, Sanicro 28, Alloy 24, Incoloy 825, Inconel 625 and Hastelloy C-276.

Values quoted are specification minima and maxima. Certified values are reported per heat on the material certificate. Page updated 5 October 2026.