Open-Die Forging Factory · Jiangyin, Jiangsu, China Tel +86-189-2135-9659  |  sales@steelforgepieces.com
Jiangyin Jiangnan Metal Co., Ltd. Open-Die Forgings · Rolled Rings · Flanges Get a Quote

X6CrNiSiNCe19-10 Forgings (EN 1.4818 / UNS S30415 / Alloy 153 MA)

Heat-resistant austenitic stainless steel. Forged rings, seamless rolled rings, flanges, shafts, discs and bars, made to drawing by Jiangyin Jiangnan Metal Co., Ltd.

X6CrNiSiNCe19-10 is the EN designation for heat-resistant austenitic stainless steel 1.4818, equivalent to UNS S30415 and to the trade name Alloy 153 MA. It carries 18–20 % Cr and 9–11 % Ni with deliberate additions of silicon, nitrogen and cerium, which stabilise the protective oxide scale and raise strength at temperature. DIN EN 10095:2018 gives an application range of 550–1050 °C; mill datasheets quote scaling resistance in air to about 1000 °C. Jiangyin Jiangnan Metal Co., Ltd., an open-die forging factory in Jiangyin, Jiangsu, China, supplies the grade as forged rings, flanges, shafts, discs, sleeves and round bars with EN 10204 3.1 or 3.2 certification.

EN number1.4818
UNSS30415
Trade nameAlloy 153 MA
StandardEN 10095
Max in air1000–1050 °C
Tensile, +AT600–800 MPa

1. Designations and equivalent grades

X6CrNiSiNCe19-10 cross-reference
Region or bodyStandardDesignation
EuropeEN 10095X6CrNiSiNCe19-10 (1.4818)
GermanyDIN EN 10095:2018-121.4818
InternationalISO 4955X6CrNiSiNCe19-10
USAUNS / ASTM A480S30415
USA, trade name—Alloy 153 MA
ChinaGB/T 2087805Cr19Ni10Si2CeN (S30450)
RussiaGOST R54908X6CrNiSiNCe19-10

Cross-reference per Stahlschlüssel 2016 and the SAE/ASTM Unified Numbering System. Equivalent grades are nominally comparable but not always interchangeable. Check against the purchase specification before substituting.

2. Chemical composition

X6CrNiSiNCe19-10 / 1.4818, percent by mass
CSiMnPSCrNiNCeFe
0.04–0.081.0–2.0≤1.0≤0.045≤0.015 18.0–20.09.0–11.00.12–0.180.03–0.08Bal. approx. 69

C, Si, Mn, P, S, Cr and Ni to EN 10095. N and Ce ranges as published for the equivalent grade 153 MA (UNS S30415). Some mill datasheets work to narrower windows, for example C ≤0.05, Cr 17.5–19.5, Ni 8.5–10.5, N ≤0.15. We melt to the range stated on the order.

Effect of the cerium addition

Cerium is what separates this grade from ordinary 304 / 1.4301. With the nitrogen and the raised silicon it gives a more adherent oxide scale, better resistance to sigma phase precipitation and higher strength at temperature. The structure stays fully austenitic, so toughness is retained down to cryogenic temperatures as well.

3. Mechanical properties at 20 °C

Solution annealed condition (+AT)
PropertyValueUnit
Tensile strength Rm600–800MPa
Proof strength Rp0.2≥ 290MPa
Elongation A5≥ 40, typically 30–40%
Hardness≤ 210HB 30
Modulus of elasticity200GPa
Application temperature in air550–1050 per EN 10095:2018°C

Figures apply to solution annealed material. Published datasheets for 153 MA quote a lower band of 500–720 MPa for thin flat product. Heavy forged sections are tested individually and the result is reported on the mill certificate.

4. Physical properties at 20 °C

DensitySpecific heat capacityThermal conductivityElectrical resistivity
7.8 g/cm³500 J/kg·K15 W/m·K0.84 Ω·mm²/m

5. Forging, heat treatment and welding

OperationParameters
Hot forming and forging900–1150 °C, followed by rapid cooling
Solution heat treatment1020–1100 °C
Cold formingGood cold forming behaviour
Welding processesSubmerged arc, plasma arc, flux cored, manual metal arc
Shielding gasArgon base with 2–3 % hydrogen for penetration and corrosion resistance
Filler metal1.4835
Selection note. 1.4818 has low resistance to oxidising sulphurous gases. It is a heat-resisting grade for hot gas and combustion products, not a seawater, subsea or sulphuric acid material. For chloride or acid service specify duplex or super-austenitic grades instead, such as A182 F51, A182 F53, A182 F55, A182 F44 or 904L.

6. Forged product forms in X6CrNiSiNCe19-10

Seamless rolled ringsRadial-axial rolled, as forged or machined
Forged flangesWeld neck, slip on, blind, orifice, special profiles
Forged shafts and spindlesStepped, eccentric and long shafts
Forged discs and blanksSolid and bored discs, tube sheets
Forged sleeves and bushingsHollow forged, trepanned bore
Forged round barsBlack, rough turned or peeled
Hollow forged pipeThick wall forged sections
Valve componentsBodies, seat rings, stems, blocks

7. Typical applications

The strongest performance window of this grade sits around 600–950 °C, so it is specified where components run continuously in hot gas. Published application areas include furnace and apparatus engineering, cement plant equipment, recuperators, hot air dryers, superheater tubes, fluidised bed components, waste combustion plant, exhaust gas preheating and hydrocarbon gas handling. In forged form that usually means burner and furnace rings, retort and muffle flanges, roller and fan shafts, grate components and heat treatment fixtures.

8. Testing, inspection and certification

Each order runs against an inspection plan agreed before release. Chemical analysis and mechanical testing are carried out in the solution annealed condition. Ultrasonic examination follows the acceptance class nominated on the order, commonly EN 10228-3, SEP 1921 or ASTM A388. Certificates are issued to EN 10204 3.1, or 3.2 with third party witness by TUV, BV, Lloyd's, SGS or the customer's own inspector. Further options on request include PMI, grain size, intergranular corrosion testing, dye penetrant examination and impact testing.

Melting route. State on the enquiry whether EAF plus AOD or VOD is acceptable, or whether a remelted ESR route is required. Both are quoted, and the route is recorded on the certificate.

9. Frequently asked questions

What is X6CrNiSiNCe19-10 equivalent to?

EN material number 1.4818, equivalent to UNS S30415 under ASTM A480, trade name Alloy 153 MA, ISO 4955 X6CrNiSiNCe19-10, GOST R54908, and Chinese GB/T 20878 grade 05Cr19Ni10Si2CeN (S30450).

What is the maximum service temperature of 1.4818?

DIN EN 10095:2018 gives 550 to 1050 °C, with a maximum application temperature up to 1050 °C in air. Supplier datasheets quote scaling resistance in air to about 1000 °C. Best performance is around 600 to 950 °C. Do not use it in oxidising sulphurous atmospheres.

Why does X6CrNiSiNCe19-10 contain cerium?

Cerium, with nitrogen and silicon, improves oxide scale stability, resistance to sigma phase precipitation and strength at high temperature compared with standard 304 type austenitic stainless steel.

How does it compare with 304 / 1.4301?

Chromium and nickel levels are similar, but 1.4818 adds silicon, nitrogen and cerium. Those additions give a more stable oxide scale, resistance to sigma phase precipitation and higher hot strength. That is why it sits in EN 10095 as a heat-resisting steel rather than in EN 10088 as a general purpose austenitic.

Can X6CrNiSiNCe19-10 be forged and welded?

Yes. Hot forming at 900 to 1150 °C with rapid cooling, then solution annealing at 1020 to 1100 °C. Welding by submerged arc, plasma arc, flux cored and manual metal arc, using argon with 2 to 3 % hydrogen. Filler 1.4835 is commonly used.

Who supplies X6CrNiSiNCe19-10 forgings?

Jiangyin Jiangnan Metal Co., Ltd., an open-die forging factory at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, produces X6CrNiSiNCe19-10 forged rings, flanges, shafts, discs and bars to drawing with EN 10204 3.1 or 3.2 certification. Telephone +86-189-2135-9659, email sales@steelforgepieces.com.

Request a quotation for X6CrNiSiNCe19-10 forgings

Send a drawing, or simply the dimensions, quantity and required standard. Quotations are normally returned within one working day.

sales@steelforgepieces.com +86-189-2135-9659

Jiangyin Jiangnan Metal Co., Ltd. · No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China

Other high temperature grades we forge: AISI 330, Incoloy 800H, Incoloy 800HT, Inconel 601, Inconel 617, Haynes 230, A286, Nitronic 60.

Page last reviewed 10 October 2026. Technical data compiled from EN 10095 and ISO 4955 publications and from published 1.4818 and UNS S30415 datasheets. Data is given for guidance. The governing documents are the agreed purchase specification and the material certificate issued with each shipment.