Open-Die Forging Factory | Jiangyin, Jiangsu, China Tel +86-189-2135-9659  |  Email sales@steelforgepieces.com
JJM Jiangyin Jiangnan Metal Co., Ltd. Open-Die Forgings | Rings | Flanges | Shafts Request a Quote

X8CrNiTi18-10 (1.4878 / AISI 321H) Open-Die Forgings

Grade data follows EN 10095. Forgings manufactured by Jiangyin Jiangnan Metal Co., Ltd., Jiangyin, Jiangsu, China.

X8CrNiTi18-10, EN material number 1.4878, is a titanium-stabilised austenitic heat-resisting stainless steel with 17 to 19 percent chromium and 9 to 12 percent nickel. It is the higher-carbon version of 1.4541, is classified as a heat-resisting steel under EN 10095, and resists scaling in air up to about 850 C. The American equivalent is AISI 321H / UNS S32109. We forge this grade to customer drawings as open-die forgings and seamless rolled rings, supplied solution annealed with EN 10204-3.1 or 3.2 certification.

Forged Products We Manufacture in This Grade

Each item is produced by open-die forging or ring rolling from vacuum-degassed ingot or billet, solution annealed, machined to drawing and inspected before despatch.

Product forms available in X8CrNiTi18-10 / 1.4878 / 321H
Product formSize rangeTypical end use
Seamless rolled ringsOD 300 to 4000 mmAnnealing and muffle furnaces, turbine casings, flange blanks
Forged rings and retaining ringsOD 200 to 2500 mmPressure vessels, towers, preheaters
Forged flangesDN15 to DN3000, to ASME B16.5 / B16.47 / EN 1092-1High-temperature piping, heat exchanger nozzles
Forged round bars and shaftsDia. 60 to 1200 mm, length to 8000 mmFurnace rolls, fan and agitator shafts, spindles
Forged discs, blanks and tube sheetsDia. 200 to 3000 mmShell and tube heat exchangers, closure heads
Forged bushings, sleeves and hollow barsOD 150 to 1500 mmHot gas ducting, expansion joints, burner components
Forged pipe, tubes and nozzlesBored or trepanned to drawingProcess modules, steam and flue gas service
Forged valve bodies, seats and stemsTo drawingHigh-temperature gate, globe, ball and check valves

Sizes outside these ranges are often possible. Send the drawing and we will confirm.

Chemical Composition of X8CrNiTi18-10 (1.4878)

Note on stabilisation. X8CrNiTi18-10 is stabilised with titanium, not niobium. A datasheet showing Nb+Ta in place of Ti describes a 347 or 347H type grade, not 1.4878. For the niobium-stabilised equivalent see AISI 347H.

Chemical composition, percent by weight, per EN 10095
ElementMinMaxFunction
Carbon (C)0.040.10Raised against 1.4541 to develop creep strength
Silicon (Si)-1.00Deoxidation, scaling resistance
Manganese (Mn)-2.00Austenite stabiliser, sulphur control
Phosphorus (P)-0.045Residual
Sulphur (S)-0.015Residual, held low for forgeability
Chromium (Cr)17.019.0Oxidation and corrosion resistance
Nickel (Ni)9.012.0Austenitic structure, toughness
Titanium (Ti)5 x C0.80Carbide stabiliser against intergranular corrosion
Iron (Fe)BalanceBase

Sulphur limits vary between standards. EN 10095 applies 0.015 percent max, while some stock material datasheets written to other standards permit up to 0.030 percent. State the governing specification on enquiry and we will melt to it.

International Equivalent Grades

Cross-reference for X8CrNiTi18-10 / 1.4878
Region and standardDesignation
Europe, ENX8CrNiTi18-10 (1.4878)
USA, AISI / ASTM / UNS321H, UNS S32109
Japan, JISSUS321H
France, AFNORZ6CNT18-10
England, BS321S12, 321S51
Italy, UNIX8CrNiTi18-11
Sweden, SS2337
Russia, GOST12KH18N10T
International, ISOX7CrNiTi18-10

Cross-references give the closest known equivalents only. Check the governing source standard for each application.

Mechanical Properties at 20 C, Solution Annealed

Room temperature properties in the solution annealed condition
PropertyValue
Tensile strength, Rm550 to 700 N/mm2, typical 610 MPa. Some standards allow 500 to 720 N/mm2
Proof strength, Rp0.2190 N/mm2 min, typical 210 MPa
Elongation A540 percent min, typical 45 percent
Hardness215 HB max, typical 180 HB
Modulus of elasticityapprox. 200 kN/mm2
Shear modulus77 GPa
Shear strength430 MPa
Fatigue strength190 MPa
Poisson ratio0.28

Physical Properties

Physical properties at 20 C unless stated
PropertyValue
Density7.9 g/cm3
Thermal conductivity15 W/m.K
Specific heat capacity480 to 500 J/kg.K
Coefficient of thermal expansionapprox. 17 micrometre/m.K
Electrical resistivity0.73 ohm.mm2/m
Melting rangeapprox. 1380 to 1430 C
Maximum service temperature, mechanicalapprox. 850 C
Magnetic responseLow, slightly magnetic after cold work
PRENapprox. 18, no molybdenum content

Corrosion, Oxidation and Temperature Behaviour

Scaling resistance. The grade resists scaling in air up to roughly 850 C and is specified for resistance to hot gases and products of combustion above 550 C. It holds up in oxidising conditions but should be kept out of carburising and sulphur-bearing atmospheres.

Creep strength. The carbon content is deliberately higher than in 1.4541, which lifts long-term creep rupture strength. That is why 1.4878 replaces 1.4541 in hot service such as heat exchangers, pressure vessels and high-temperature piping.

Intergranular corrosion. Titanium ties up carbon as titanium carbide, so chromium carbide cannot form at the grain boundaries. The grade resists intergranular attack both solution annealed and as welded, which matters for welded structures carrying combined thermal and pressure loads.

Not seawater resistant. There is no molybdenum in 1.4878, so it pits and suffers crevice attack in chloride-rich media. General corrosion resistance is good in low-chloride environments, but in strongly acidic or chloride-laden service it is only conditionally resistant. For marine, subsea or brine duty use A182 F51, A182 F55 or A182 F44.

Forging, Heat Treatment, Welding and Machining

Melting practice

We melt X8CrNiTi18-10 by electric arc furnace with VOD refining. Electro-slag remelting is available where tighter cleanliness, better through-thickness ductility or reduced segregation is called for on critical rotating or pressure-retaining parts.

Hot forging

Forging runs from about 1150 C down to a finish temperature near 900 C, followed by rapid cooling. We hold enough deformation ratio through the section to break down the cast structure and reach a uniform fine grain.

Heat treatment

Solution anneal only. X8CrNiTi18-10 is fully austenitic and cannot be hardened by quenching or ageing. Forgings are solution annealed at roughly 1020 to 1070 C and cooled rapidly, which dissolves carbides and restores ductility and corrosion resistance. A datasheet describing solution plus ageing for this grade is describing a precipitation-hardening steel such as 17-4PH, not 1.4878.

Welding

1.4878 welds by all conventional processes, with or without filler metal, and no post-weld heat treatment is required. Titanium cuts the hot cracking risk. Matching Ti or Nb stabilised consumables are normally used.

Machining

Like every austenitic stainless steel, this grade work-hardens under the cutting edge. Sharp rigid tooling, positive rake, heavy uninterrupted feed, reduced surface speed and plenty of coolant keep the cut below the hardened layer. With those settings it machines without trouble.

Testing, Inspection and Certification

Every X8CrNiTi18-10 forging is produced under a documented inspection and test plan.

Standard test scope for 1.4878 forgings
TestStandard or method
Chemical analysisLadle and product analysis by spectrometer
Ultrasonic testingEN 10228-3, SEP 1921, ASTM A388
Mechanical testingTensile, elongation, reduction of area, hardness. Impact on request
Intergranular corrosionASTM A262 Practice E on request
Surface NDTLiquid penetrant to ASTM E165 on request
Dimensional reportFull inspection against customer drawing
CertificationEN 10204-3.1 standard, EN 10204-3.2 with third-party witness

Typical Applications for X8CrNiTi18-10 Forgings

Industrial furnaces and heat treatment. Rolled rings and forged shafts for annealing furnaces, muffle furnaces, hardening boxes, furnace rolls and radiant tube supports, where the 850 C scaling limit and the creep strength decide the material choice.

Pressure equipment and heat exchangers. Forged tube sheets, flanges, shells, nozzles and forged pipe for shell and tube heat exchangers, pressure vessels and air receivers running above 550 C.

Chemical and petrochemical plant. Forged rings, flanges and shafts for columns and towers, reactors, tanks, silos, process modules and preheaters. The grade is also used across pulp and paper and food processing.

Power generation and rotating equipment. Forged spindles, gears, bars and rings for turbines, gas compressors, power transmission and gearboxes working at elevated temperature.

High-temperature valves. Forged bodies, seats, seat rings, stems and blocks for gate, globe, ball, plug, check and strainer assemblies in hot service.

Exhaust and flue gas. Forged manifolds, ducting parts and expansion joint components under repeated thermal cycling, where the stabilised structure prevents sensitisation.

1.4878 Compared with Neighbouring Grades

Choosing between X8CrNiTi18-10 and related forging grades
GradeStabiliserChoose it when
X8CrNiTi18-10 / 1.4878 / 321HTitaniumSustained service above 550 C needing creep strength and scaling resistance to 850 C
1.4541 / A182 F321TitaniumLower carbon version for ambient and moderate temperature duty
AISI 347H / A182 F347NiobiumNiobium stabilisation specified, or titanium loss across the arc is a concern
Incoloy 800H-Service well above 850 C, or carburising atmospheres where 1.4878 does not suit
A182 F44 / A182 F51Mo-bearingChloride, seawater or brine exposure where 1.4878 would pit

Frequently Asked Questions

What is X8CrNiTi18-10?
EN material number 1.4878, a titanium-stabilised austenitic heat-resisting stainless steel with 17 to 19 percent chromium and 9 to 12 percent nickel. It is the heat-resisting, higher-carbon version of 1.4541 and sits under EN 10095. The American equivalent is AISI 321H, UNS S32109.
What is the American equivalent of 1.4878?
AISI and ASTM 321H, UNS S32109. Elsewhere it corresponds to SUS321H in Japan, Z6CNT18-10 in France, 321S12 and 321S51 in England, X8CrNiTi18-11 in Italy, SS 2337 in Sweden, 12KH18N10T in Russia and X7CrNiTi18-10 under ISO.
What is the maximum service temperature?
Around 850 C for scaling resistance in air. The grade is intended for hot gases and products of combustion above 550 C. It is not suitable for carburising or sulphur-rich atmospheres.
Why is titanium added to this steel?
Titanium binds carbon as titanium carbide, which stops chromium carbide forming at the grain boundaries. Chromium stays in solution where it protects the steel, so the grade resists intergranular corrosion after welding or long thermal exposure. The required range is 5 times carbon up to 0.80 percent titanium.
Is X8CrNiTi18-10 seawater resistant?
No. With no molybdenum it is open to pitting and crevice corrosion in chloride-rich environments. For seawater or marine service choose a molybdenum-alloyed grade such as 1.4404, or a duplex grade.
How are the forgings heat treated?
Solution annealed only, roughly 1020 to 1070 C with rapid cooling. Being fully austenitic, 1.4878 cannot be hardened by quenching or ageing.
Can it be welded?
Yes, by all conventional processes with or without filler metal, and no post-weld heat treatment is needed. Titanium lowers the hot cracking risk.
What is the difference between 1.4541 and 1.4878?
Both are titanium-stabilised austenitic grades. 1.4878 carries higher carbon, between 0.04 and 0.10 percent, which raises creep strength, so it is the one chosen for high-temperature duty. 1.4541 is the usual pick at lower temperatures.
Who manufactures X8CrNiTi18-10 open-die forgings?
Jiangyin Jiangnan Metal Co., Ltd., an open-die forging factory at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China. We produce forged rings, seamless rolled rings, flanges, shafts, discs, bushings, sleeves, tube sheets and forged pipe in 1.4878 to customer drawings, with EN 10204-3.1 or 3.2 certification. Telephone +86-189-2135-9659, email sales@steelforgepieces.com.

Request a Quotation for X8CrNiTi18-10 Forgings

Send a drawing or specification, or just the outside diameter, inside diameter, height and quantity. You will have a price, weight and lead time back, usually within one working day.

About the Manufacturer

Jiangyin Jiangnan Metal Co., Ltd. is an open-die forging factory at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China. We produce open-die forgings, seamless rolled rings, forged flanges, forged bars, shafts, discs, bushings, sleeves and tube sheets in carbon steel, alloy steel, tool steel, stainless steel and nickel alloys, working from customer drawings and the governing specification. Enquiries in English and Chinese reach us at +86-189-2135-9659 or sales@steelforgepieces.com.

A plain-text version of this datasheet is available at x8crniti18-10.md.