Open-Die Forging Factory · Jiangyin, Jiangsu, China Tel: +86-189-2135-9659 sales@steelforgepieces.com
Jiangyin Jiangnan Metal Co., Ltd. Open-die forgings, rings, bars, discs, shafts Get a Quote for S165M Forgings

S165M Stainless Steel Forgings (EN 1.4418 / X4CrNiMo16-5-1 / SS 2387)

Open-die forged bars, hollow bars, sleeves, seamless rolled rings, discs, blocks, shafts, hydro turbine blades and centrifuge bodies, made to your drawing by Jiangyin Jiangnan Metal Co., Ltd.

S165M is the Swedish designation for the low-carbon, soft-martensitic chromium-nickel-molybdenum stainless steel standardised as EN 1.4418 / X4CrNiMo16-5-1 and SS 2387. With carbon held at 0.06 % maximum plus 15-17 % Cr, 4-6 % Ni and 0.8-1.5 % Mo, it reaches up to 1150 MPa tensile strength in +QT900 while keeping good fatigue resistance, good low-temperature toughness and good weldability. Its corrosion resistance is better than that of the classic hardenable martensitic stainless steels. Jiangyin Jiangnan Metal Co., Ltd. forges this grade into bars, rings, discs, sleeves, shafts and turbine blades at its open-die forging plant in Jiangyin, Jiangsu, China.

  • Grade family: low-carbon soft-martensitic stainless steel. Some suppliers describe it as martensitic-austenitic because of retained austenite.
  • Key designations: S165M, EN 1.4418, X4CrNiMo16-5-1, SS 2387, Z8CND17.04, 248SV.
  • Delivery conditions: +A (annealed), +QT760, +QT840, +QT900.
  • Forging standard: EN 10250-4 for open-die stainless steel forgings.
  • Our scope: forged blanks and rough-machined parts, ultrasonically tested, with EN 10204 3.1 or 3.2 certificates.
Note on the designation. "AISI S165M" is not a valid grade name. S165M comes from the Swedish SS system (SS 2387), and the European standard name is X4CrNiMo16-5-1 (1.4418). This grade has no direct ASTM or AISI equivalent. If your specification calls for a US standard grade, please confirm the intended grade with us before ordering. In most cases buyers are comparing it against 17-4PH or 15-5PH.

S165M equivalents and applicable standards

Cross-reference designations for S165M / EN 1.4418
System or countryDesignation
EN steel number1.4418
EN steel nameX4CrNiMo16-5-1
Sweden (SS)S165M, SS 2387, SS2387
France (AF / AIR 9160)Z6CND16-05-01, Z8CND17.04, Z8CND17-04
Other works names248SV, X164M, BMS H-10, FE-PM3504, 081753 / 1753
CIS / Russian08Kh17N5M3 (08H17N5M3, Kh17N5M3)
ASTM / AISINo direct equivalent published

The grade appears in the following European standards, which is why it is regularly specified for forged and pressure-retaining parts.

Standards covering 1.4418 / X4CrNiMo16-5-1
StandardScope
EN 10250-4Open steel die forgings for general engineering purposes, stainless steels
EN 10088-1Stainless steels, list of stainless steels
EN 10088-2Sheet, plate and strip for general purposes
EN 10088-3Semi-finished products, bars, rods, wire, sections, bright products
EN 10088-4 / -5Flat and long products for construction purposes
EN 10272Stainless steel bars for pressure purposes
EN 10028-7Flat products of stainless steels for pressure purposes

S165M / 1.4418 chemical composition

Composition in weight %, iron balance. Values per EN 10088-1 (1.4418), SS (S165M / SS 2387) and AIR 9160 (Z8CND17.04).
Standard / gradeCSiMn PSCrNi MoN
EN 1.4418 / X4CrNiMo16-5-1≤0.06≤0.70≤1.50≤0.040≤0.03015.0-17.04.0-6.00.8-1.5≥0.02
SS 2387 / S165M≤0.05≤1.00≤1.50≤0.045≤0.03015.0-17.04.0-6.00.8-1.5–
AF Z6CND16-05-01≤0.06≤1.00≤1.00≤0.040≤0.02515.0-17.03.5-5.50.80-1.25–
AIR 9160 Z8CND17.04 (nominal)0.05–0.75––16.05.01.00.03

A typical melt aim is around 16 % Cr, 5 % Ni and 1.0 to 1.2 % Mo with carbon at or below 0.06 %. Where your drawing sets tighter limits than the standard, state them at enquiry stage so we can select the melt accordingly.

Mechanical properties of S165M / 1.4418

Room-temperature properties by delivery condition, bar and forged bar. Rm tensile strength, Re yield strength, A elongation, KV20 impact energy.
ConditionRm (MPa)Re min (MPa)A min (%)KV20 min (J)Hardness
+A annealed, over 16 mm≤1100–––≤320 HB
+A annealed, small sections≤1150–––≤380 HB
+QT760760-9605501670–
+QT840840-11006601455–
+QT900900-11507001060–

Properties at elevated temperature

Minimum Rp0.2 in MPa at temperature, with modulus and expansion values.
Property100 °C150 °C200 °C250 °C300 °C400 °C
Rp0.2, +QT760≥520≥510≥500≥490≥480–
Rp0.2, +QT840 / +QT900≥660≥640≥620≥600≥580–
Modulus of elasticity E (GPa)195–185–175170
Linear expansion (10-6 K-1)10.3–10.8–11.211.6

Properties measured on a finished forging depend on section size, forging reduction and the position the test coupon is taken from. For heavy rings, discs and shafts we agree the test location, coupon orientation and acceptance values with you before production, so the certificate reflects the governing section.

Physical properties

Room-temperature physical data for 1.4418 / S165M.
PropertyValue
Density7.7 g/cm³
Modulus of elasticity200 GPa
Specific heat capacity430 J/(kg·K)
Thermal conductivity15 W/(m·K)
Electrical resistivity0.8 µΩ·m

Heat treatment of S165M forgings

Soft annealing (+A)

600-650 °C (1112-1202 °F), cooled in air or in the furnace. Heat uniformly to temperature.

Hardening

950-1050 °C (1742-1922 °F), oil or air quench. The +QT840 route uses 900-1000 °C. Light sections harden adequately on air cooling.

Tempering for +QT900

550-620 °C (1022-1148 °F), oil or air cool. Both a single long hold and two shorter cycles with intermediate cooling are used in practice.

Tempering for +QT760 and +QT840

+QT760 at 590-620 °C. +QT840 at 570-650 °C after the 900-1000 °C hardening step.

Our shop practice is to avoid holding or slow-cooling these forgings through the 450-550 °C band, because soft-martensitic Cr-Ni-Mo stainless steels can lose toughness when tempered in that window. If your drawing specifies a tempering temperature inside that range, we will raise it with you before release rather than simply following the note.

Corrosion resistance

This grade brings corrosion behaviour close to that of austenitic steel to a hardenable stainless steel. Published data puts its corrosion resistance on a level with 18-8 austenitic grades, with good strength and corrosion resistance in welded joints and good behaviour at low temperature. It performs in mild atmospheric, industrial and domestic environments and in potable and mine waters, in both annealed and heat-treated condition. Typical service is at low concentration and room temperature in media such as acetic acid, citric acid, salt solutions, pyrogallic acid, tannin, stearic acid and certain nitrates and sulphur compounds.

Surfaces must be free of scale, lubricants, foreign particles and any coatings used for drawing or heading. After machining or fabrication, cleaning and passivation should be considered. We can supply forgings pickled and passivated on request.

S165M / 1.4418 forgings we manufacture

All items below are produced as open-die forgings or seamless rolled rings to your drawing or dimensional list, as forged, rough-machined or finish-machined.

Forged bars

Round bars and rods, square, rectangular and flat bars, hexagonal bars.

Hollow forgings

Hollow bars, sleeves, bushes and bushings, forged pipe and tube, barrels, casings, shells, cylinders, hubs and housings.

Seamless rolled rings

Rolled and forged rings, retaining rings, ring blanks for bearings and gears.

Discs, blocks and plates

Forged discs and disks, blocks, slabs and plate-form forgings.

Hydro turbine components

Kaplan and Francis hydroelectric and hydraulic water turbine blades and runner components.

Shafts and spindles

Pump shafts, spindles, pistons, pins, crankshafts and injector bodies.

Centrifuge parts

Disc-stack and decanter centrifuge bowls, bodies, hoods and covers.

Other forgings

Valve bodies, agitator parts, flanges and further forged components to specification.

Testing, inspection and certification

S165M forged rings and other products are ultrasonically tested to the standard you nominate. EN 10228-3, SEP 1921 and ASTM A388 are the ones most often applied to this grade. Certificates are issued to EN 10204 3.1, or EN 10204 3.2 with third-party endorsement where the project requires it. Chemical analysis, mechanical testing, hardness survey, dimensional report, PMI, liquid penetrant examination and grain size or microstructure examination can be added to the inspection plan. Send us the governing specification and we will return a proposed test and acceptance plan together with the quotation.

Where S165M is used

Because it holds high strength and fatigue resistance without the corrosion penalty of ordinary martensitic grades, S165M / 1.4418 is specified for valves, turbine sub-assemblies, shafts, pins, pistons, spindles, crankshafts, bolts and nuts, and agitators. The main industries are chemical processing, power generation including hydro, marine and shipbuilding, and aviation and cryogenic equipment.

Frequently asked questions

What is S165M stainless steel?

S165M is the Swedish designation for the low-carbon soft-martensitic chromium-nickel-molybdenum stainless steel standardised in Europe as EN 1.4418 / X4CrNiMo16-5-1 and in Sweden as SS 2387. It contains a maximum of 0.06 % carbon with 15.0-17.0 % chromium, 4.0-6.0 % nickel and 0.8-1.5 % molybdenum, giving high strength and fatigue resistance together with good weldability and better corrosion resistance than traditional hardenable martensitic stainless steels.

Is there an AISI or ASTM equivalent to S165M / 1.4418?

No. S165M is an SS (Swedish) designation rather than an AISI grade, and EN 1.4418 / X4CrNiMo16-5-1 has no direct ASTM equivalent. The recognised cross-references are SS 2387, Z8CND17.04 and Z6CND16-05-01 (AIR 9160), 248SV, X164M, BMS H-10 and 08Kh17N5M3. Buyers working to US standards most often benchmark it against 17-4PH and 15-5PH.

What are the +QT900 properties of 1.4418?

In +QT900 condition, bar products reach 900-1150 MPa tensile strength with minimum 700 MPa yield strength, minimum 10 % elongation and minimum 60 J KV20 impact energy. +QT840 gives 840-1100 MPa with 660 MPa minimum yield and 14 % minimum elongation. +QT760 gives 760-960 MPa with 550 MPa minimum yield, 16 % minimum elongation and 70 J minimum impact energy.

How do you heat treat S165M forgings?

Soft annealing is at 600-650 °C with air or furnace cooling. Hardening is at 950-1050 °C with oil or air quench, followed by tempering at 550-620 °C for +QT900 or 590-620 °C for +QT760. The +QT840 route hardens at 900-1000 °C and tempers at 570-650 °C.

Can S165M be welded?

Yes. Good weldability is one of the main reasons this grade is chosen, and published data reports good strength and corrosion resistance in welded joints. The welding procedure, filler selection and any post-weld heat treatment still need to be qualified for your joint design and section thickness.

Who manufactures S165M open-die forgings?

Jiangyin Jiangnan Metal Co., Ltd., an open-die forging factory at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, produces S165M / EN 1.4418 / SS 2387 forged bars, hollow bars, sleeves, seamless rolled rings, discs, shafts, hydro turbine blades and centrifuge bowls to customer drawings, with ultrasonic testing to EN 10228-3, SEP 1921 or ASTM A388 and EN 10204 3.1 or 3.2 certificates. Contact sales@steelforgepieces.com or +86-189-2135-9659.

What information do you need to quote?

A drawing or the finished dimensions, the delivery condition required (+A, +QT760, +QT840 or +QT900), the quantity, the governing specification, the NDT and certificate requirement, and the delivery port. If no drawing is available yet, outside diameter, inside diameter, height or length and weight are enough for a first price.

Request a price for S165M / 1.4418 forgings

Send the size or drawing of the S165M forged part you need and we will quote the price, forging route and lead time. Jiangyin Jiangnan Metal Co., Ltd., No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China.

Email sales@steelforgepieces.com Call +86-189-2135-9659

Related grades for forged stainless parts

Composition, property and heat treatment figures on this page follow the published requirements of EN 10088-1, EN 10088-3, EN 10250-4 and the Swedish SS 2387 and AIR 9160 specifications, and are given for guidance. The values that govern an order are those in the agreed specification and on the material certificate.

Jiangyin Jiangnan Metal Co., Ltd., open-die forging factory, Jiangyin, Jiangsu, China. Page updated . For technical clarification or a quotation contact sales@steelforgepieces.com or +86-189-2135-9659.